BOSCH Repairs - Services

Ph: 0408 359 072

Bosch code pads emit a sound because it wants to bring to your attention that it now requires a service  – This means a trouble fault condition has happened. If the plug pack is unplugged or the mains POWER is disconnected the code pad will beep once every minute. If you disconnect the main alarm battery the system may start beeping. To silence, press 5 and hold until code pad beeps twice and now will then display type of fault,. Press # to exit this feature. Note that silencing the code pad will not stop the beeping permanently. The beeping will return. As long as the initial cause of trouble remains the code pad keeps sounding until the fault is rectified. Refer to your manual for help

The best solution to stop your Bosch beeping alarm keypad

THERE ARE THREE WAYS TO STOP THE BOSCH ALARM FROM BEEPING

The best way to stop your Bosch alarm system from beeping is to get it serviced straight away if you can. If the beeping starts in the middle of the night this would be very annoying problem so take action to restore this situation immediately. In most cases there maybe  a flat battery in the control box so you can stop the alarm beeping yourself by replacing the old flat battery. This is is a very common problem to many security systems in Australia. Sometimes doing this service yourself can be a hard job to do if you cannot locate the central control panel and the associated components. Another way to stop an alarm beeping keypad is to shut down the whole alarm system so then we need to locate the power point and disconnect the battery. So having said that the final alternative step to stop the alarm beeping would be to mute the sound coming from the keypad. To do this step press and hold the "5" button down until you hear two beeps as this method will only temporarily stop the noise until you get the system serviced. The fault is usually recognized on the keypad by the name "FAULT”  displayed with LED KEYPADS or a triangle shape with an Exclamation Mark   shown with ICON LCD KEYPADS

What causes a beeping alarm keypad ?

There a quiet a number of factors which will make this happen. If you move into a new home with an existing security system please have it serviced straight away otherwise your code pad might start making a beeping sound. More than likely the beeping is due to a flat battery because the power was turned off due to new ownership settlement. This fault is very common issue in Australia.. A beeping alarm code pad can also occur due to the  telephone communications network that has a fault connection to the modem. In this case your burglar alarm won`t stop beeping so arrange to have the problem fixed. Planned or unplanned power outages may cause an alarm beeping keypad constantly so to avoid this situation  change your alarm battery in time. Fuse faults caused by a short circuit may also start a beeping code pad every minute and a cut telephone line fault maybe the cause towards a beeping sound keypad as well. And finally the best way to avoid a beeping keypad is to replace the batteries in time which is best to put in a calendar for routine maintenance. Please refer to the reasons for a beeping alarm keypad as follows.

Common issues to a beeping alarm keypad!

Please refer to your alarm manual in the section "fault diagnostic table" to fix this problem. Our friendly licensed team provide service across Melbourne to help this issue. We fix your beeping Bosch security equipment whether recent, obsolete, old or new. We will assign an expert technician to fix or stop your alarm beeping code pad.

Low battery and Loss of Power to your security system:

After 5 years the typical backup battery in a device will be very weak. In this case you may also have a beeping code pad. System devices contain batteries that have to be replaced. The beeping alarm code pad gives you a trouble status when the battery levels are low. In most cases a flat battery can trigger a beeping alarm code pad. Loss of mains power can also be the cause as well as a power outage in your area. The battery supplies back-up power during loss of mains and should last for up to 20 hours. Wireless devices with a flat battery in a security system can make a beeping code pad which will require battery replacements.

Smoke detectors connected to alarm system

A battery operated smoke detector with a flat battery also emits a single "chirp" sound once every 30 seconds, making attention to users that the smoke detector battery is very weak. If you do not replace a fire alarm low battery this may sound continuously and can be very annoying. The low battery chirping comes on as a warning that battery needs immediate replacing. This can also sound a Bosch alarm beeping so please change this battery immediately. Important: Use only batteries recommended by your security company.

       More helpful instructions to Bosch security alarm systems!

SERVICE STATUS FAULT LIST:

Press and HOLD number 5 until 2 beeps are heard

Zone light indicates FAULT condition.  Refer to alarmmaintenance.com.au data sheets. Once fault type is identified. Enter # to exit this feature. code pad beeps will sound

The fault light indicator lights if the system detects a panel fault. Every time a new system fault is detected the FAULT  indicator flashes and code pad beeping every minute.

PHONE LINE TEST REPORT – Press 9 until code pad beeps

SIREN – Press 1 and hold until code pad beeps – siren will sound for 2 seconds.  BELL – Press 2 until code pad beeps – internal siren will sound for 2 seconds.  STROBE LIGHT – Press 3 until you hear three beeps – this will turn strobe light ON. Repeat, press 3 until you hear three beeps to turn strobe off. Test reporting to a monitored alarm panel can be sent without sounding the siren. press and HOLD the 9 button until code pad beeps

We can service your BOSCH SECURITY CODEPAD FAULT LIGHT FLASHING | Exclamation mark inside a TRIANGLE SYMBOL DISPLAYED  for LCD KEYPADS | BOSCH BEEPING ALARM CODEPAD | BOSCH MAINS LIGHT FLASHING KEYPAD -  ALARM CODEPAD  REPLACEMENTS | SECURITY ALARM FALSE ALARMING

YOUR BOSCH HOME SECURITY SYSTEM BEEPING INDICATES THERE IS A SYSTEM FAULT WAITING TO BE ADDRESSED TO CODE PADS Models like 488 404 880 Ultima 862, 844, ICP-CC488, Bosch ICP-CC4XX 16i 16+ 2000 3000 6000